Emergency help needed (again): Timing question (16V)

[flaatr at yahoo.com (Euroroc II)]

What cams did you install?
-Raffi


At 01:42 AM 7/10/2003 -0400, Ryan H wrote:
>If you mean the notch in the tranny bellhousing, I don't have one!  So, 
>I'm lining up the flywheel mark by the center of the hole.  So far, it 
>runs smoother than before, so I may have did it right.  I've even got the 
>timing advanced a bunch and it runs baby smooth.  The cams aren't as 
>powerful as I was expecting, but I'm gonna fiddle with mixture.  Oh well.
>
> >
> > From: "John Lagnese" <jlagnese@massed.net>
> > Date: 2003/07/10 Thu AM 12:26:52 EDT
> > To: "Ryan H" <rhock99@epix.net>
> > Subject: Re: Emergency help needed (again): Timing question (16V)
> >
> > I can't recall which direction the engine turns, but it wouldn't be 
> pointing
> > at the notch @TDC. So it will be near the notch.
> > ----- Original Message -----
> > From: "Ryan H" <rhock99@epix.net>
> > To: "John Lagnese" <jlagnese@massed.net>
> > Cc: <scirocco-l@scirocco.org>
> > Sent: Thursday, July 10, 2003 12:07 AM
> > Subject: Re: Emergency help needed (again): Timing question (16V)
> >
> >
> > > OK, I just need confirmation:  with the cam marks dead even with the top
> > of the head (chain-side), where should the flywheel mark be, in the center
> > of the hole or pointing straight up?
> > >
> > > >
> > > > From: "John Lagnese" <jlagnese@massed.net>
> > > > Date: 2003/07/09 Wed PM 10:29:52 EDT
> > > > To: "Ryan H" <rhock99@epix.net>
> > > > Subject: Re: Emergency help needed: Timing question (16V)
> > > >
> > > > Did you use the mark on the inside of the timing belt gear? If you used
> > the
> > > > one on the front, or fender side its off. The mark should be 
> visible and
> > but
> > > > lines up with the notch @ 6' BTDC
> > > > ---- Original Message -----
> > > > From: "Ryan H" <rhock99@epix.net>
> > > > To: <scirocco-l@scirocco.org>
> > > > Sent: Wednesday, July 09, 2003 2:22 AM
> > > > Subject: Emergency help needed: Timing question (16V)
> > > >
> > > >
> > > > > OK, I just put a new set of cams in, and the camshaft pulley mark is
> > > > perfectly straight up, the intercam marks are dead on, and I think I
> > kept
> > > > the timing belt in the same spot (99% sure).  But, my flywheel mark,
> > > > although pointed straight up, is hardly visible in the hole because the
> > hole
> > > > is slightly offset.  Is it right pointed straight up, or should it 
> be in
> > the
> > > > middle of the hole?  Thanks!!!
> > > > >
> > > > >
> > > > > _______________________________________________
> > > > > Scirocco-l mailing list
> > > > > Scirocco-l@scirocco.org
> > > > > http://neubayern.net/mailman/listinfo/scirocco-l
> > > >
> > > >
> > >
> > >
> > > _______________________________________________
> > > Scirocco-l mailing list
> > > Scirocco-l@scirocco.org
> > > http://neubayern.net/mailman/listinfo/scirocco-l
> >
> >
>
>
>_______________________________________________
>Scirocco-l mailing list
>Scirocco-l@scirocco.org
>http://neubayern.net/mailman/listinfo/scirocco-l