[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
8v Distributor woes...
Speaking of the 3A block; what would my CR be if I put a 86 GTi head on
it,that's been shaved .040" ??? Many thanks....Ken R.
----- Original Message -----
From: "Dan Bubb" <jdbubb@ix.netcom.com>
To: <pbureau@attbi.com>
Cc: "Kervin" <kervinridgley@earthlink.net>; <scirocco-l@scirocco.org>
Sent: Friday, September 27, 2002 11:00 AM
Subject: Re: 8v Distributor woes...
> Patrick:
> You're putting a JH head on a 3A block. Right??
> My understanding is the JH head and 3A head have the same combustion
> chamber volume, so changing heads should make no difference in CR.
> The only data I can find indicates the 3A had a 10.5 CR, so that would
> be your CR also, but I may be wrong.
> Dan
> Still looking for some hard data on 3A CR since my nephew wants to do
> this also.
>
> pbureau@attbi.com wrote:
> >
> > HUmm A little confused..
> >
> > you have a distributor I Want?
> >
> > all I need is the JH with the 3a gear on it to make this
> > work. Knock box.. who needs a knock box.. this aint
> > going to produce 11:1 compression all my data indicates
> > 9.4:1...am I wrong?
> >
> > now you mentioned an adaptor plate? I am assuming this
> > is an aftermarket parts, any idea who sells this?
> >
> > GREG! Heeeeeeellllp!
> > --
> > ====
> > ATS - Patrick Bureau
> > 1985 8v Euro GTX 3A/JH Project
> > (show car)
> > 1985 8v Euro GT Project (Daily Drive)
> > http://www.longcoeur.com/scirocco/
> > http://www.texassciroccoteam.org/
> > > There is a pin that holds the gear on. Drive the pin out of both,
swap
> > > gears and use the JH distributor. If you are going to use a knock
> > > sensor, I think you have to use something other than the vacuum
advance
> > > type. I have the distributor that you need sitting here, cause I got
> > > another one to use with my knock sensor. *important* Put the adapter
> > > ring on your JH distributor before you put the bigger gear on. The
gear
> > > is too big to fit through the hole in the ring.
> > >
> > > pbureau@attbi.com wrote:
> > > >
> > > > okay started getting organized to do my hybrid 3a/jh
> > > > engine, and I am looking at the 3a distributor and I was
> > > > told to keep CIS I needed to transfer the gear from teh
> > > > 3s distro to the JH distro... can anyone advise me how
> > > > do you get that gear off the shaft?
> > > >
> > > > no I cannot use the 3a distro, top parrt of it was
> > > > damaged from yard hacking (someone tried to pull the
> > > > distro off the head without proper tools)
> > > >
> > > > --
> > > > ====
> > > > ATS - Patrick Bureau
> > > > 1985 8v Euro GTX 3A/JH Project
> > > > (show car)
> > > > 1985 8v Euro GT Project (Daily Drive)
> > > > http://www.longcoeur.com/scirocco/
> > > > http://www.texassciroccoteam.org/
> > > >
> > > > _______________________________________________
> > > > Scirocco-l mailing list
> > > > Scirocco-l@scirocco.org
> > > > http://neubayern.net/mailman/listinfo/scirocco-l
> > >
> > > --
> > > Kervin
> > > 86 Scirocco 2.0 8v 4K+80%
> > > 88 Gti 1.8 16v needs some love
> > > 00 tt600
> > >
> >
> > _______________________________________________
> > Scirocco-l mailing list
> > Scirocco-l@scirocco.org
> > http://neubayern.net/mailman/listinfo/scirocco-l
>
> _______________________________________________
> Scirocco-l mailing list
> Scirocco-l@scirocco.org
> http://neubayern.net/mailman/listinfo/scirocco-l