Upper Strut Tie bar Question

[scirocco16vr32 at gmail.com (Chris Bennett)]

I am not sure what the Callaway has I would have to go look but I can take
pictures if you like.  It has the front and rear.  I can look for part
numbers.  The front has the collars on the struts and the rear is a straight
(square) bar between the two upper points.  Looks to be steel if I
remember...

Let me know.  I gotta mow the yard anyway today so I will be right there
looking at it to get the mower out.

Chris


On 8/3/06, Allyn <amalventano1@tds.net> wrote:
>
> For A1 you need a specific Neuspeed part.  The autotech part has
> additional mounting holes in the collar that support installation
> on a MK1.  I'm not 100% on this one, someone back me up please.
>
> HTH
> Al
>
> > -----Original Message-----
> > From: Gordy Stedman [mailto:ydrogs@gmail.com]
> > Sent: Wednesday, August 02, 2006 6:54 PM
> > To: Lance LaPrarie; Scirocco-l@scirocco.org
> > Subject: Re: Upper Strut Tie bar Question
> >
> > 3A block so deck height is the same.  I was told by the
> > person who gave me the bar that it was for a rabbit which
> > should be the same as a Scirocco since both A1, although the
> > rabbits strut towers are lower in the engine compartment from
> > the top of the fenders than a Scirocco.  Tried to put it on
> > my friends bunny and it was the same story.  I got it from
> > Ty, the guy with the grey Corrado race car at WW, when I
> > bought my G60 from him.  He threw it in for free so I took
> > it.  I am guessing it is for a MK2 and will try it on my
> > buddy's GTI if I ever make it back home again.  I can get 2
> > holes to line up on one strut bearing but they are no where
> > close on the other side.
> >
> > On 8/2/06, Lance LaPrarie <sciroccojunky@gmail.com> wrote:
> > >
> > >  Hey Gordy,
> > >
> > > Was this supposed to be for Mark I? I know if I take mine off on an
> > > uneven surface it can cause your car to shift and whe you
> > take the bar
> > > off the holes don't line up. I just went through this last week. I
> > > pulled it off the car earlier last weekand waited a few
> > days to finish
> > > what I was doing Turns out that the body had shifted and wouldn't
> > > allow the bar to go back on easily. Also, what block are
> > you running?
> > > ABA blocks don't allow for placement of a stress barin the
> > usual way,
> > >
> > > Just an FWI.
> > >
> > >
> > > Thanks!!
> > >
> >
> > --
> > Gordy
> > MK1 x 4
> > MK2 x 1
> > _______________________________________________
> > Scirocco-l mailing list
> > Scirocco-l@scirocco.org
> > http://neubayern.net/mailman/listinfo/scirocco-l
>
>
> _______________________________________________
> Scirocco-l mailing list
> Scirocco-l@scirocco.org
> http://neubayern.net/mailman/listinfo/scirocco-l
>



-- 
80 Scirocco Callaway Indiana Red
85 Scirocco 16v (conversion) Burgundy
87 Scirocco 16v Tornado Red
04 R32 Reflex Silver