Feeler: MS unit with harness

[rogercv1 at gmail.com (Roger)]

give you $80 for it

On 4/7/06, Derrick floyd <tyrone27@gmail.com> wrote:
> Any one have a price?
>
> On 4/7/06, Derrick floyd <tyrone27@gmail.com> wrote:
> >
> > i'm using hall signal.  it shows constant chang and its just jumping
> > around.  I can look at the tach on the instrument cluster and see somethign
> > is wrong because its just all over the place.  T3bunny modied it again
> > because I was going to use the fidle to control the isv.
> >
> >
> > On 4/7/06, Dan Bubb <jdbubb@verizon.net> wrote:
> > >
> > > Do the datalogs show consistent RPM change or is the RPM just jumping
> > > around???
> > > I thought I modified your unit for a hall sensor ignition input, but it
> > > sounds like you're using the crank wheel and VR sensor for an input. Did
> > > T3bunny modify it again, or is my memory effed up?
> > > Are the ignition sensor wires shielded and is the shield grounded?
> > > Dan
> > >
> > > From: "Derrick floyd" <tyrone27@gmail.com>
> > > Sent: Friday, April 07, 2006 7:08 AM
> > > Subject: Re: Feeler: MS unit with harness
> > >
> > >
> > > the fuel part mostly.  I need to find someone with MS extra that is
> > > runing
> > > there spark setup like mine to test this unit in a car.
> > >
> > > On 4/7/06, Dan Bubb < jdbubb@verizon.net> wrote:
> > > >
> > > > WHAT couldn't you get to run right?
> > > > You haven't even had the thing in for a week and you're giving up?
> > > > What part doesn't work?
> > > >
> > > >
> > > > From: "Derrick floyd" <tyrone27@gmail.com>
> > > > Sent: Thursday, April 06, 2006 9:21 PM
> > > >
> > > >
> > > > yup couldn't get it to run right.  so i'm going back to tec2
> > > >
> > > > On 4/6/06, Roger <rogercv1@gmail.com> wrote:
> > > > >
> > > > > why are you selling it??? didnt you just install it???
> > > > >
> > > > > On 4/6/06, Derrick floyd < tyrone27@gmail.com> wrote:
> > > > > > I'm just putting this out there to see how much I can probably get
> > > for
> > > > > my
> > > > > > equipment. I have a MS-1 unit made by Dan bubb and modified my t3
> > > > bunny.
> > > > > >
> > > > > > Wire harness was made by T3bunny and its a complete plug and play
> > > > > harness
> > > > > > for a scirocco 16v.
> > > > > >
> > > > > > here are the pics:
> > > > > >
> > > > > > http://forum.vwsport.com/pics/data/500/medium/100_0351.JPG
> > > > > > http://forum.vwsport.com/pics/data/500/medium/100_0350.JPG
> > > > > > http://forum.vwsport.com/pics/data/500/medium/IMAG0020.JPG
> > > > > > _______________________________________________
> > > >
> > > >
> > >
> > >
> > >
> >
> _______________________________________________
> Scirocco-l mailing list
> Scirocco-l@scirocco.org
> http://neubayern.net/mailman/listinfo/scirocco-l
>