Rebuilding with molly lub

[txrocco at sbcglobal.net (ATS - Patrick Bureau)]

for the first break in period (3000 miles) I strickly used ND30 in the
engine, changing oil and filter every 1000 miles (yes I am anal but I know
this way any shards of metal are out of the system), then I switched to
standard 20w50.


ATS - Patrick Bureau - txrocco@sbcglobal.net
----------------------------------------------
MSN:ATSGTX@hotmail.com |YAHOO:ATSGTX@yahoo.com
ICQ:32918816           |AIM:Texasscirocco
----------------------------------------------


=>-----Original Message-----
=>From: shawn f [mailto:falzsf@mts.net]
=>Sent: Friday, September 26, 2003 12:16 PM
=>To: ATS - Patrick Bureau
=>Cc: scirocco list
=>Subject: Re: Rebuilding with molly lub
=>
=>
=>So using ND30 is fine. Good that was what i was planning on
=>doing. I know i
=>was told i should run ND20w50 for engine break in but i am having a hard
=>time finding it. Anyideas? I live in winnipeg, manitoba, canada.
=>
=>Shawn F
=>----- Original Message -----
=>From: "ATS - Patrick Bureau" <txrocco@sbcglobal.net>
=>To: "Dan Bubb" <jdbubb@ix.netcom.com>; "shawn f"
=><falzsf@mts.net>; "scirocco
=>list" <scirocco-l@scirocco.org>
=>Sent: Friday, September 26, 2003 10:55 AM
=>Subject: RE: Rebuilding with molly lub
=>
=>
=>> the only lube an engine needs when rebuilding it is ND30 (non
=>detergent 30
=>> weight oil) I usually used 2 qtrs during rebuilds
=>>
=>>
=>> ATS - Patrick Bureau - txrocco@sbcglobal.net
=>> ----------------------------------------------
=>> MSN:ATSGTX@hotmail.com |YAHOO:ATSGTX@yahoo.com
=>> ICQ:32918816           |AIM:Texasscirocco
=>> ----------------------------------------------
=>>
=>>
=>> =>-----Original Message-----
=>> =>From: scirocco-l-bounces@scirocco.org
=>> =>[mailto:scirocco-l-bounces@scirocco.org]On Behalf Of Dan Bubb
=>> =>Sent: Friday, September 26, 2003 10:32 AM
=>> =>To: shawn f; scirocco list
=>> =>Subject: Re: Rebuilding with molly lub
=>> =>
=>> =>
=>> =>Definitely not on the pistons and rings (perhaps those should be
=>assembled
=>> =>dry?). I'd think it would be good most other places as long
=>as it isn't
=>> =>wheel bearing Moly lube. That would be a little heavy!
=>> =>Dan
=>> =>
=>> =>----- Original Message -----
=>> =>From: "shawn f" <falzsf@mts.net>
=>> =>To: "scirocco list" <scirocco-l@scirocco.org>
=>> =>Sent: Friday, September 26, 2003 10:49 AM
=>> =>Subject: Rebuilding with molly lub
=>> =>
=>> =>
=>> =>What does everyone think of rebuilding the engine with molly lube? If
=>yes
=>> =>where should i use it. I belive they say use iot on the top of
=>> =>the cam caps
=>> =>not sure where else though.
=>> =>_______________________________________________
=>> =>Scirocco-l mailing list
=>> =>Scirocco-l@scirocco.org
=>> =>http://neubayern.net/mailman/listinfo/scirocco-l
=>> =>
=>> =>
=>> =>
=>> =>_______________________________________________
=>> =>Scirocco-l mailing list
=>> =>Scirocco-l@scirocco.org
=>> =>http://neubayern.net/mailman/listinfo/scirocco-l
=>>
=>>
=>