intermediate shaft (more qurestions)sc

[falzsf at mts.net (shawn f)]

Well my delear can get the intermediate shaft bearin but they arnt prepared,
so i guess i need to use a brake cylinder hone to hone them down? Or should
i buy the ones from techtonics that are done already. Maybe just goto a
machine shop and get the to match it to the shaft. For installing them can i
just push them in or does it take quite a force?

Thanks again dude.!!
----- Original Message ----- 
From: "David Utley" <mr.utility@highstream.net>
To: "shawn f" <falzsf@mts.net>; "Drew MacPherson"
<drew@scirocco.cs.uoguelph.ca>
Cc: "scirocco list" <scirocco-l@scirocco.org>
Sent: Sunday, October 12, 2003 12:07 AM
Subject: RE: intermediate shaft


> The dealer cannot get them, believe it or not...  Any competent machine
> shop, TT, or Potterman should be able to get them...
>
> David/ fahrvegnugen
>
> -----Original Message-----
> From: scirocco-l-bounces@scirocco.org
> [mailto:scirocco-l-bounces@scirocco.org]On Behalf Of shawn f
> Sent: Saturday, October 11, 2003 12:27 PM
> To: Drew MacPherson
> Cc: scirocco list
> Subject: Re: intermediate shaft
>
> yes i am having problems finding them. I phoned a vw dealer and they wernt
> sure about tthat part! PRETTY BAD, i guess techtonics or germanautoparts
> should have em....
> ----- Original Message -----
> From: "Drew MacPherson" <drew@scirocco.cs.uoguelph.ca>
> To: "shawn f" <falzsf@mts.net>
> Cc: "scirocco list" <scirocco-l@scirocco.org>
> Sent: Saturday, October 11, 2003 12:14 PM
> Subject: Re: intermediate shaft
>
>
> >
> >
> > I think they're harder to source than they are to install.  I've never
> > done it but I believe they can be driven in.
> >
> > Drew
> >
> > On Sat, 11 Oct 2003, shawn f wrote:
> >
> > > how hard are they to install?
> > >
> > > I have some pics too, just to make sure....
> > >
> > > http://wpggamer.org/inter/index.html
> > >
> > > ----- Original Message -----
> > > From: "Drew MacPherson" <drew@scirocco.cs.uoguelph.ca>
> > > To: "shawn f" <falzsf@mts.net>
> > > Cc: "scirocco list" <scirocco-l@scirocco.org>
> > > Sent: Saturday, October 11, 2003 11:39 AM
> > > Subject: Re: intermediate shaft
> > >
> > >
> > > >
> > > > If the machine shop used a chemical hot tank to clean the block,
then
> the
> > > > intermediate shaft bearings may well have disolved - requiring new
> ones to
> > > > be installed.
> > > >
> > > > Drew
> > > >
> > > >
> > > > On Sat, 11 Oct 2003, shawn f wrote:
> > > >
> > > > > I was checking the intermediate shaft and i have major play. Could
> the
> > > bearing have been removed by the machine shop? I slide it in and it
has
> > > major movement on the innner bearing. Is the bearing seperate since it
> seem
> > > that the shaft moves around quite a bit near the distributor
> side....Ahhhhh
> > > possible another delay....
> > > > > _______________________________________________
> > > > > Scirocco-l mailing list
> > > > > Scirocco-l@scirocco.org
> > > > > http://neubayern.net/mailman/listinfo/scirocco-l
> > > > >
> > > >
> > > > --
> > > > /=============================================\
> > > > |  84 Wolfsburg Edition TurboDiesel Scirocco  |
> > > > |    http://scirocco.cs.uoguelph.ca/gtd       |
> > > > \=============================================/
> > > >
> > > >
> > >
> > >
> > >
> > > _______________________________________________
> > > Scirocco-l mailing list
> > > Scirocco-l@scirocco.org
> > > http://neubayern.net/mailman/listinfo/scirocco-l
> > >
> >
> > --
> > /=============================================\
> > |  84 Wolfsburg Edition TurboDiesel Scirocco  |
> > |    http://scirocco.cs.uoguelph.ca/gtd       |
> > \=============================================/
> >
> >
>
>
>
> _______________________________________________
> Scirocco-l mailing list
> Scirocco-l@scirocco.org
> http://neubayern.net/mailman/listinfo/scirocco-l
>
>