[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Pedal assembly help needed.

Subject: Pedal assembly help needed.
From: jtoomasson at yahoo.com (Jeff Toomasson)
Date: Mon Dec 1 22:11:23 2003
In-reply-to: <002a01c3b891$57f52c40$63e5a818@main>
Bravo, Al !! 

I was just going to _say_ it, but a pic does say a thousand words!  :)

JT


Allyn <amalventano@sc.rr.com> wrote:
aah, the advantages to having a gutted rocco in the garage:
http://scirocco.dhs.org/vw/pics/0-allyn/project/space%20frame/images/image20.htm
your culpret is in the center of that pic.
hth
Al

----- Original Message ----- 
From: "Ryan H" 
To: "Dave Ewing" 
Cc: 
Sent: Monday, December 01, 2003 11:25 PM
Subject: Re: RE: Pedal assembly help needed.


> OK, I've got everything out of the way - steering column is dropped,
nothing is connected to the pedal assembly bracket in the engine bay. And
the pedal assembly still won't budge. I stared and stared at it trying to
find another bolt holding it to the dash or somewhere, but I can't find it.
It's got to be there, otherwise they tack welded my pedal assembly bracket
to the firewall, cause it's TIGHT.
> So, anyone know where else there are bolts on the pedal assembly? I've
got the three that go through the firewall taken care of.
> Thanks all (especially Dave for all the help!)
>
> >
> > From: "Dave Ewing" 
> > Date: 2003/11/28 Fri AM 04:07:53 EST
> > To: "Ryan H" 
> > Subject: RE: Pedal assembly help needed.
> >
> > You'll have to take the bolts off that attach the column to the
underside of
> > the dash. This will drop the column down and probably take care of most
of
> > your problems. Be careful as it may cause a little stress on your wires
for
> > your combo switch and ignition switch (you may want to disconnect them).
> > Anyhoo, try that and it should help out greatly. I am pretty sure there
are
> > no other bolts on the pedal assy but make sure you look around there
could
> > be one anchoring it down to the bottom part of the dash as well (I
really
> > don't think so though--I think I'm mistaking this for an A2--A1s and A2s
are
> > WAY different). So you already removed the little plate on the column
to
> > pedal assy??? If so, you are VERY close!!! Good luck and LMK how
things
> > work out. Hope you had a wonderful Turkey day!
> >
> >
> > Dave
> >
> > -----Original Message-----
> > From: Ryan H [mailto:rhock99@epix.net]
> > Sent: Tuesday, November 25, 2003 9:05 PM
> > To: Dave Ewing
> > Subject: Re: Pedal assembly help needed.
> >
> >
> > OK, Dave sorry to be a pain:
> > I've got everything on the engine bay side out; booster, bracket, etc.
The
> > pedal assembly still doesn't want to budge though - there's a plastic
ring
> > around the steering column that it fits snug against, and I think this
may
> > be the reason. How did you remove this? It's the ring that the little
> > metal plate (previously removed) was resting against. I tried tapping
it
> > out with a hammer and screwdriver, but it just sorta chips. But once I
get
> > the assembly loose, how do you "drop" the steering column? I've got the
> > bolt that holds the u-joint together loose, but the steering shaft
doesn't
> > just pop out of it (i.e. they're tight together). Any other hints
greatly
> > appreciated. Thanks for all your help Dave, you're a lifesaver!
> > Ryan H.
> > >
> > > From: "Dave Ewing" 
> > > Date: 2003/11/17 Mon PM 05:56:49 EST
> > > To: "Ryan H" 
> > > Subject: RE: Pedal assembly help needed.
> > >
> > > They are back there, I guarantee it!! BUT, yes, it is tough to get to
but
> > > not impossible. I have this really nice Snap-On "S" wrench that I use
for
> > > diesel injection pumps that helps some on those but usually just a
stubby
> > 13
> > > will do the trick for you. If I remember correctly a couple are where
you
> > > can see them and a couple are kinda hidden so you have to feel for
them.
> > > Your fore arms will know you've been working them after this job!
> > >
> > > Anyway, your on the right track and this is the hardest part of the
job.
> > > After that it's pretty smooth sailing!
> > >
> > > Dave
> > >
> > > -----Original Message-----
> > > From: Ryan H [mailto:rhock99@epix.net]
> > > Sent: Wednesday, November 12, 2003 4:28 PM
> > > To: Dave Ewing
> > > Subject: RE: Pedal assembly help needed.
> > >
> > >
> > > OK Dave, I finally got somemore time to work on this thing. Got the
brake
> > > fluid res drained and off, but I can't see any of the bolts - are they
on
> > > the back of the booster or front? If they're on the back, how the
heck
> > did
> > > you get to them, I can't even fit my hand in that space! Thanks,
> > > Ryan H.
> > >
> > > >
> > > > From: "Dave Ewing" 
> > > > Date: 2003/11/08 Sat AM 06:49:29 EST
> > > > To: "Ryan H" 
> > > > Subject: RE: RE: Pedal assembly help needed.
> > > >
> > > > Yeah, I may have goofed on the reverse light thing and you don't
have to
> > > > remove the accelerator cable, that's on A2s.
> > > >
> > > > You are right on track and what you said, as far as the next steps
are
> > > > concerned, are correct. The little plate that goes around the
column
> > has
> > > to
> > > > be removed because this connects the column to the pedal assy and,
> > > > unfortunately, you will probably have to drop the column down some
to
> > > wiggle
> > > > the pedal assy out. Once you look under your dash you will
understand
> > > what
> > > > I am talking about. You pry it off with a screw driver (big but
small
> > > > enough to fit down there) and then you have to tap in back in place
when
> > > > installing. There are little slots or ears that catch when you do
this.
> > > > Once you take it apart it will make more sense. LMK on your
progress,
> > > looks
> > > > like things are going well!
> > > >
> > > > Dave
> > > >
> > > > -----Original Message-----
> > > > From: Ryan H [mailto:rhock99@epix.net]
> > > > Sent: Wednesday, November 05, 2003 6:51 PM
> > > > To: Dave Ewing
> > > > Cc: rhock99@epix.net
> > > > Subject: Re: RE: Pedal assembly help needed.
> > > >
> > > >
> > > > OK Dave, things are going better now... I got the plate off,
> > disconnected
> > > > the brake light switch (is that what you meant by reverse switch?),
> > > > disconnected the brake "pushrod" going to the booster, disconnected
the
> > > > clutch cable and throttle cable (don't think i needed to do the last
> > > part -
> > > > the gas pedal isn't connected to the whole assembly).
> > > > Anyway, now let me see if I have this straight: I remove four bolts
> > > > directly on the back of the booster that hold it to the bracket,
then
> > > gently
> > > > put the master/booster out of the way. Then I remove the 3 (?)
bolts
> > that
> > > > hold the bracket to the firewall. These bolts also hold the pedal
> > > assembly
> > > > bracket, right? And what little plate around the steering column do
you
> > > > mean? Why remove it?
> > > > Thanks for your help Dave!
> > > > Ryan H.
> > > >
> > > > >
> > > > > From: "Dave Ewing" 
> > > > > Date: 2003/10/28 Tue PM 08:25:53 EST
> > > > > To: "Ryan H" 
> > > > > Subject: RE: Pedal assembly help needed.
> > > > >
> > > > > It's pretty simple, actually. First, disconnect the shaft from
the
> > > brake
> > > > > master, disconnect the throttle cable and pop out the reverse
light
> > > switch
> > > > > (on most Mk2s, Mk1s have the back up switch on the master).
Remove
> > the
> > > 4
> > > > > bolts on the back of the booster then you can remove the bracket
that
> > is
> > > > > bolted to the pedal assy through the firewall. I can't remember
if
> > A1s
> > > > have
> > > > > the anchor bolt up top but I know you have to pop the little plate
off
> > > > from
> > > > > around the column. You may have to drop the column down to be
able to
> > > > move
> > > > > it around enough to take out but it really isn't that tough once
you
> > > start
> > > > > in on it. If you have any questions along the way you can email
me
> > > since
> > > > I
> > > > > have pretty much stranded on the computer until I get caught up in
my
> > > CAD
> > > > > class and I check my email frequently!
> > > > >
> > > > > Dave
> > > > > -----Original Message-----
> > > > > From: scirocco-l-bounces@scirocco.org
> > > > > [mailto:scirocco-l-bounces@scirocco.org]On Behalf Of Ryan H
> > > > > Sent: Tuesday, October 28, 2003 4:01 PM
> > > > > To: scirocco-l@scirocco.org
> > > > > Subject: Pedal assembly help needed.
> > > > >
> > > > >
> > > > > Any tips or how tos on removing the pedal assembly? The little
> > cylinder
> > > > > that holds the clutch cable in the firewall snapped, so I believe
I
> > need
> > > > to
> > > > > remove it in order to weld it back on (or just get a new
assembly).
> > > > Thanks!
> > > > >
> > > > >
> > > > > _______________________________________________
> > > > > Scirocco-l mailing list
> > > > > Scirocco-l@scirocco.org
> > > > > http://neubayern.net/mailman/listinfo/scirocco-l
> > > > > ---
> > > > > Incoming mail is certified Virus Free.
> > > > > Checked by AVG anti-virus system (http://www.grisoft.com).
> > > > > Version: 6.0.530 / Virus Database: 325 - Release Date: 10/22/2003
> > > > >
> > > > > ---
> > > > > Outgoing mail is certified Virus Free.
> > > > > Checked by AVG anti-virus system (http://www.grisoft.com).
> > > > > Version: 6.0.530 / Virus Database: 325 - Release Date: 10/22/2003
> > > > >
> > > > >
> > > >
> > > > ---
> > > > Incoming mail is certified Virus Free.
> > > > Checked by AVG anti-virus system (http://www.grisoft.com).
> > > > Version: 6.0.537 / Virus Database: 332 - Release Date: 11/6/2003
> > > >
> > > > ---
> > > > Outgoing mail is certified Virus Free.
> > > > Checked by AVG anti-virus system (http://www.grisoft.com).
> > > > Version: 6.0.537 / Virus Database: 332 - Release Date: 11/6/2003
> > > >
> > > >
> > >
> > > ---
> > > Incoming mail is certified Virus Free.
> > > Checked by AVG anti-virus system (http://www.grisoft.com).
> > > Version: 6.0.538 / Virus Database: 333 - Release Date: 11/10/2003
> > >
> > > ---
> > > Outgoing mail is certified Virus Free.
> > > Checked by AVG anti-virus system (http://www.grisoft.com).
> > > Version: 6.0.538 / Virus Database: 333 - Release Date: 11/10/2003
> > >
> > >
> >
> > ---
> > Incoming mail is certified Virus Free.
> > Checked by AVG anti-virus system (http://www.grisoft.com).
> > Version: 6.0.543 / Virus Database: 337 - Release Date: 11/21/2003
> >
> > ---
> > Outgoing mail is certified Virus Free.
> > Checked by AVG anti-virus system (http://www.grisoft.com).
> > Version: 6.0.543 / Virus Database: 337 - Release Date: 11/21/2003
> >
> >
>
>
> _______________________________________________
> Scirocco-l mailing list
> Scirocco-l@scirocco.org
> http://neubayern.net/mailman/listinfo/scirocco-l


_______________________________________________
Scirocco-l mailing list
Scirocco-l@scirocco.org
http://neubayern.net/mailman/listinfo/scirocco-l

---------------------------------
Do you Yahoo!?
Protect your identity with Yahoo! Mail AddressGuard
Follow-Ups:
- Pedal assembly help needed.
  - From: amalventano at sc.rr.com (Allyn)
References:
- Pedal assembly help needed.
  - From: amalventano at sc.rr.com (Allyn)
Prev by Date: Pedal assembly help needed.
Next by Date: Pedal assembly help needed.
Previous by thread: Pedal assembly help needed.
Next by thread: Pedal assembly help needed.
Index(es):
- Date
- Thread