[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Tach signal / knock sensor power increase?
- Subject: Tach signal / knock sensor power increase?
- From: bhonnold@pac-cap.com (Brian Honnold)
- Date: Wed, 2 Apr 2003 09:43:03 -0800
- In-reply-to: <C434A1A59F0DC141B1589A40411EE74429C611@pcmserver01.Pacificcapital.local>
That trick only applies to the early systems on 1985 RD motors.
> -----Original Message-----
> From: scirocco-l-admin@scirocco.org
> [mailto:scirocco-l-admin@scirocco.org] On Behalf Of Joe Doty
> Sent: Wednesday, April 02, 2003 9:16 AM
> To: Ryan H; scirocco-l@scirocco.org
> Subject: RE: Tach signal / knock sensor power increase?
>
>
> Is this what you're talking about? This is something I saved
> from somewhere a while back:
>
> > The computer for the knock control has two ignition maps
> you can use,
> > Europeon (Hot) and North American (Cold). The base timing on a big
> > valve head, 1985 and up is 6 deg btdc and with the knock sensor and
> > Euro ignition map you can push your timing to 12 - 15 btdc.
> With these
> > two changes you get about 5 - 10 hp gain and when you use super
> > unleaded you can feel the difference. (you can also change
> to a Euro
> > ignition map in any CIS-E powered motor by cutting the
> jumper from pin
> > 3 to pin 11 on the knock sensor control unit and don't forget to
> > advance the ignition) This is such an easy conversion, I would
> > encourage everybody to do it.
>
> Joe Doty
> IT/Development
> joe@lcnetwork.com
>
> > humm i though the TAch signal (rpm) was the pin 7 of the TZH box not
> the
> > knock box.
> >
> > ATS - Patrick Bureau - txrocco@sbcglobal.net
> >
> >
> > =>-----Original Message-----
> > =>From: scirocco-l-admin@scirocco.org
> > =>[mailto:scirocco-l-admin@scirocco.org]On Behalf Of Ryan H
> > =>Sent: Tuesday, April 01, 2003 11:20 PM
> > =>To: scirocco-l@scirocco.org
> > =>Subject: Tach signal / knock sensor power increase?
> > =>
> > =>
> > =>OK guys, can someone tell me what wire to/from the knock box
> > =>(16V) is the tach signal? And also, look at this pic.... in the
> > =>bottom right it says something about increasing power by
> > =>unconnecting two grounds... um, anyone try this? Where are they
> > =>connected together? At the harness connection?
> >
> =>http://home.mindspring.com/~tberk/_uimages/Knock-Sensor-Diagram.JPG
> > =>
> > =>
> > =>_______________________________________________
> > =>Scirocco-l mailing list
> > =>Scirocco-l@scirocco.org
> > =>http://neubayern.net/mailman/listinfo/scirocco-l
> >
> >
> > _______________________________________________
> > Scirocco-l mailing list
> > Scirocco-l@scirocco.org
> > http://neubayern.net/mailman/listinfo/scirocco-l
>
> _______________________________________________
> Scirocco-l mailing list
> Scirocco-l@scirocco.org
> http://neubayern.net/mailman/listinfo/scirocco-l
>