[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Mk2 questions
This is a multi-part message in MIME format.
------=_NextPart_000_0127_01C28CBD.2A7196B0
Content-Type: text/plain;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
on the topic of the resistor, i think the one on the rieger is going, =
and i dont feel like building a pcm/igbt electronic controller for it =
just yet. are these packs sold seperate from the fan unit? if so, how =
much?
Al
----- Original Message -----=20
From: Robbie Cotner=20
To: scirocco81@vwmail.net=20
Cc: scirocco-l@scirocco.org=20
Sent: Friday, November 15, 2002 3:28 PM
Subject: Re: Mk2 questions
to get to the resistor pack/blower fan you go in from under the hood(a =
little bit of under dash work too, nothing horrible). Remove the rain =
tray and the HVAC intake, and then you'll see the motor. Remove the =
screw, and pull it towards the passenger side to get it out(a little =
more complex than that, but it's self-explanatory). HTH-=20
Rob=20
Eric S <scirocco81@vwmail.net> wrote:=20
Me being the mk1 guy that I am...I know little about the specific =
stuff to mk2s....IE, heater controls, etc. My new 83 has a couple of =
issues....
Ok, fan works, but 1,2 and 4 are all the same as 4, 3 position acts =
like 1. I assume this is the resistor pack going bad? If so, where is it =
on the mk2s with A/C?
Second, would a late model (large gas tank, mini spare) cat back =
exhaust fit on the early model (small tank, full size spare) mk2? =
(thinking no)
Third: The heater controls are whacked. air only comes outta the =
vent, moving the slider makes no noises (that vaccum "hiss" I am used to =
on the A/C VWs). And apparently the damn think thinks its in the A/C =
position......turn on the blower fan, a/c engages as does the radiator =
fan on slow speed. So, I assume I gotta dig the controls out and see =
what is broken. Um...how do I do that on a Mk2? Do I have to pull the =
cente! r console? Does anyone have a GOOD working heater control from an =
A/C equipped Mk2?
The rest I can handle...warped rotors, brake system needs a bleed or =
a M/C, new clutch cable is in order I think...this one seems =
stretched...can't get enough adjustment for the new clutch...it engages =
WAY too early (like 1/10th of an inch off the floor, ton of free play at =
the top)...check and re-balance the rear tires...might have something =
else going on (rear wheel bearing? Something was giving me a rythmic =
(comes and goes) vibration at 75, not felt in the wheel, but in the =
butt...whole car was shaking...suggestions welcome here...what does a =
bad inner CV act like? Similar?). Also, MOTOR MOUNTS! Man....I don't =
think I've felt a passenger side motor mount so bad before...vibe city =
at idle and 3200 rpm or so...
Last I have to figure out is, what the HELL that noise is when the =
car is backed up....someone to walk along side the car and listen should =
clear that up...I'll check in! to that on Sunday.
--
Eric
Northglenn, CO
81 Scirocco S (*TDI* swap and complete restoration in holding =
pattern)
81 Rabbit Truck LX Diesel (Waiting for BAE Turbo Install)
83 Scirocco Wolfsburg
87 Suzuki Samurai JX Hardtop (Soon to be VW Turbo Diesel Powered)
91 Cabriolet (2.0 Crossflow 8v swap and mechanical rebuild in =
progress)
_______________________________________________
Scirocco-l mailing list
Scirocco-l@scirocco.org
http://neubayern.net/mailman/listinfo/scirocco-l
-------------------------------------------------------------------------=
-----
Do you Yahoo!?
Yahoo! Web Hosting - Let the expert host your site
------=_NextPart_000_0127_01C28CBD.2A7196B0
Content-Type: text/html;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=3DContent-Type content=3D"text/html; =
charset=3Diso-8859-1">
<META content=3D"MSHTML 6.00.2800.1106" name=3DGENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=3D#ffffff>
<DIV><FONT face=3DArial size=3D2>on the topic of the resistor, i think =
the one on=20
the rieger is going, and i dont feel like building a pcm/igbt electronic =
controller for it just yet. are these packs sold seperate from the fan =
unit? if=20
so, how much?</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>Al</FONT></DIV>
<DIV> </DIV>
<BLOCKQUOTE=20
style=3D"PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; =
BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style=3D"FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV=20
style=3D"BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: =
black"><B>From:</B>=20
<A title=3Drobw_z@yahoo.com href=3D"mailto:robw_z@yahoo.com";>Robbie =
Cotner</A>=20
</DIV>
<DIV style=3D"FONT: 10pt arial"><B>To:</B> <A =
title=3Dscirocco81@vwmail.net=20
href=3D"mailto:scirocco81@vwmail.net";>scirocco81@vwmail.net</A> </DIV>
<DIV style=3D"FONT: 10pt arial"><B>Cc:</B> <A =
title=3Dscirocco-l@scirocco.org=20
href=3D"mailto:scirocco-l@scirocco.org";>scirocco-l@scirocco.org</A> =
</DIV>
<DIV style=3D"FONT: 10pt arial"><B>Sent:</B> Friday, November 15, 2002 =
3:28=20
PM</DIV>
<DIV style=3D"FONT: 10pt arial"><B>Subject:</B> Re: Mk2 =
questions</DIV>
<DIV><BR></DIV>
<P>to get to the resistor pack/blower fan you go in from under the =
hood(a=20
little bit of under dash work too, nothing horrible). Remove the =
rain=20
tray and the HVAC intake, and then you'll see the motor. Remove =
the=20
screw, and pull it towards the passenger side to get it out(a little =
more=20
complex than that, but it's self-explanatory). HTH-=20
<P>Rob=20
<P> <B><I>Eric S <<A=20
=
href=3D"mailto:scirocco81@vwmail.net";>scirocco81@vwmail.net</A>></I></=
B>=20
wrote:=20
<BLOCKQUOTE=20
style=3D"PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #1010ff 2px =
solid"><BR>Me=20
being the mk1 guy that I am...I know little about the specific stuff =
to=20
mk2s....IE, heater controls, etc. My new 83 has a couple of=20
issues....<BR><BR>Ok, fan works, but 1,2 and 4 are all the same as =
4, 3=20
position acts like 1. I assume this is the resistor pack going bad? =
If so,=20
where is it on the mk2s with A/C?<BR><BR>Second, would a late model =
(large=20
gas tank, mini spare) cat back exhaust fit on the early model (small =
tank,=20
full size spare) mk2? (thinking no)<BR><BR>Third: The heater =
controls are=20
whacked. air only comes outta the vent, moving the slider makes no =
noises=20
(that vaccum "hiss" I am used to on the A/C VWs). And apparently the =
damn=20
think thinks its in the A/C position......turn on the blower fan, =
a/c=20
engages as does the radiator fan on slow speed. So, I assume I gotta =
dig the=20
controls out and see what is broken. Um...how do I do that on a Mk2? =
Do I=20
have to pull the cente! r console? Does anyone have a GOOD working =
heater=20
control from an A/C equipped Mk2?<BR><BR>The rest I can =
handle...warped=20
rotors, brake system needs a bleed or a M/C, new clutch cable is in =
order I=20
think...this one seems stretched...can't get enough adjustment for =
the new=20
clutch...it engages WAY too early (like 1/10th of an inch off the =
floor, ton=20
of free play at the top)...check and re-balance the rear =
tires...might have=20
something else going on (rear wheel bearing? Something was giving me =
a=20
rythmic (comes and goes) vibration at 75, not felt in the wheel, but =
in the=20
butt...whole car was shaking...suggestions welcome here...what does =
a bad=20
inner CV act like? Similar?). Also, MOTOR MOUNTS! Man....I don't =
think I've=20
felt a passenger side motor mount so bad before...vibe city at idle =
and 3200=20
rpm or so...<BR><BR>Last I have to figure out is, what the HELL that =
noise=20
is when the car is backed up....someone to walk along side the car =
and=20
listen should clear that up...I'll check in! to that on=20
Sunday.<BR><BR>--<BR>Eric<BR>Northglenn, CO<BR><BR>81 Scirocco S =
(*TDI* swap=20
and complete restoration in holding pattern)<BR>81 Rabbit Truck LX =
Diesel=20
(Waiting for BAE Turbo Install)<BR>83 Scirocco Wolfsburg<BR>87 =
Suzuki=20
Samurai JX Hardtop (Soon to be VW Turbo Diesel Powered)<BR>91 =
Cabriolet (2.0=20
Crossflow 8v swap and mechanical rebuild in=20
=
progress)<BR><BR>_______________________________________________<BR>Sciro=
cco-l=20
mailing=20
=
list<BR>Scirocco-l@scirocco.org<BR>http://neubayern.net/mailman/listinfo/=
scirocco-l</BLOCKQUOTE>
<P><BR>
<HR SIZE=3D1>
Do you Yahoo!?<BR><A=20
=
href=3D"http://rd.yahoo.com/hosting/mailsig/*http://webhosting.yahoo.com"=
>Yahoo!=20
Web Hosting</A> - Let the expert host your =
site</BLOCKQUOTE></BODY></HTML>
------=_NextPart_000_0127_01C28CBD.2A7196B0--