Shifter bushing kit

[kywes@bellsouth.net (Wes Brockway)]

Back to the drawing board!

In a fit I just moved the shift finger in pretty close to the guide
plate (underneath). Now I have a 3-D transmission! All the way down and
forward for Reverse, halfway down and forward for First, and just
forward for Third. Sheeesh

So necxt time I get a chance I am going to move the shift finger just a
little bit away from the guide plate and retest.

At least I did find a bad vacumn hose. Now she does run a little better,
I just can't shift gears.

-----Original Message-----
From: Euroroc II [mailto:flaatr@yahoo.com] 
Sent: Monday, April 08, 2002 7:33 PM
To: Wes Brockway; Scirocco-l@scirocco.org
Subject: RE: Shifter bushing kit


Oh, Gottcha!

Now I know what you mean.

-RGK-

At 06:56 PM 4/8/02 -0400, you wrote:
>The button connector as I am calling it is a small flat round end that 
>sits on a short post on the sensor. A spade lug slides over it. As 
>opposed to a sensor with a spade connector that accepts a spade 
>connector.
>
>-----Original Message-----
>From: Euroroc II [mailto:flaatr@yahoo.com]
>Sent: Monday, April 08, 2002 4:04 PM
>To: Wes Brockway; Scirocco-l@scirocco.org
>Subject: Re: Shifter bushing kit
>
>
>Button connector? Locking connector with a release on the side? Not 
>sure
>
>about that but the thermo-time switch is in that area.
>
>-Raffi
>
>
>At 02:57 PM 4/8/02 -0400, you wrote:
> >I've gotten all bushings installed and things are a lot better 
> >however the ball of the shift lever has a lot of play to where it 
> >translates to
>
> >at least a .25" if not .5" variation underneath the car at the 
> >reverse lock out rod (for want of a better description)My bushing set

> >came from
>
> >the local VW dealership with the shift lever repair kit.
> >
> >Question - Is there a better aftermarket kit (not counting short 
> >shift
> >kits)
> >
> >Other question - what fuel injection seal kit do you guys recommend 
> >and
>
> >are they available from our list supporters. I got a set again from 
> >the
>
> >local VW dealer and not all the seals fit my injectors.
> >
> >Last question this post. - I'm preparing to camp out with the Bentley

> >for a while but maybe one of you guys will know immediately. In 
> >checking out things I noticed yet another sensor on my cylinder head 
> >with nothing attached to it. This one juts out in the same direction 
> >as
>
> >the distributor and is on the back side of the end of the head, 
> >normally hidden by the distributor. For reference there is another 
> >connector on the end of the head in front of the distributor, same 
> >orientation, that has a flat connector. The one in back that I am 
> >interested in has the button kind of connector. HTH
> >
> >BTW I have an '87 16V Pl engine
> >
> >
> >
> >_______________________________________________
> >Scirocco-l mailing list
> >Scirocco-l@scirocco.org 
> >http://neubayern.net/mailman/listinfo/scirocco-l
>
>
>
>_________________________________________________________
>
>Do You Yahoo!?
>
>Get your free @yahoo.com address at http://mail.yahoo.com



_________________________________________________________

Do You Yahoo!?

Get your free @yahoo.com address at http://mail.yahoo.com