[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
RE: Exhaust manifold-downpipe studs? Replaceable?
While Kano doesn't sell through retail outlets, they have a toll-free number
by which you can place a credit card order. I recently purchased two 11-oz.
cans of Aerokroil for $11, shipping included. I don't know if they still
have that deal running (2-for-1 with free shipping, I think), but even if
they don't, I think it would be worth the money to order it regardless of
the cost.
Incidentally, according to an old ACVW mechanic I know, it's the only stuff
to use on Beetle door hinge pins. When I was in college, I took my Beetle
to him to have a CV joint replaced (wasn't equipped to do the work at the
time), and he dropped a little Kroil into the hinges while I was there.
They had been tight enough that they would cause the A-pillar to flex when I
swung the door, and they freed up quite nicely pretty quickly.
Aaron
'87 528e
'82 Scirocco
'70 Beetle
'82 GPz550
-----Original Message-----
From: owner-scirocco-l@scirocco.org
[mailto:owner-scirocco-l@scirocco.org]On Behalf Of Fry, Larry
Sent: Tuesday, October 30, 2001 12:51 PM
To: aaron@makuta.com; 'Bob & Ann'; 'Victor Farren';
mpeters6@rochester.rr.com; scirocco-l@scirocco.org
Subject: RE: Exhaust manifold-downpipe studs? Replaceable?
Aaron is quite right about the WD-40 vs. the real thing, and his advice on
Kroil is excellent, too bad Kano's products are not available in retail
outlets....
BTW, the stud remover device is also available from www.mcmaster.com.
enjoy the ride
Larry sandiego16V
-----Original Message-----
From: Aaron Ness [mailto:aaron@makuta.com]
Sent: Tuesday, October 30, 2001 7:37 AM
To: Fry, Larry; 'Bob & Ann'; 'Victor Farren'; mpeters6@rochester.rr.com;
scirocco-l@scirocco.org
Subject: RE: Exhaust manifold-downpipe studs? Replaceable?
I was in an exhaust shop having some work done, and while I was there, the
guy was removing some studs from another manifold someone brought in. He
had a Snap-On socket that somehow grips studs (I didn't see what was inside,
and have never had a chance to look at one), and he was hitting them with a
torch and a spray bottle full of water. He said the steam somehow loosened
them to a point that he could turn them out with his stud extractor, and
that he never uses penetrating fluid.
I know most of us probably don't have access to an acetylene torch (I
typically don't), so penetrating fluid and a propane torch have worked well
for me in the past. BTW, don't confuse WD-40 with a legitimate penetrating
fluid. If you can, get your hands on some Kroil <http://www.kanolabs.com>
or PB.
Aaron
'87 528e
'82 Scirocco
'70 Beetle
'82 GPz550
-----Original Message-----
From: owner-scirocco-l@scirocco.org
[mailto:owner-scirocco-l@scirocco.org]On Behalf Of Fry, Larry
Sent: Tuesday, October 30, 2001 9:23 AM
To: Bob & Ann; Victor Farren; mpeters6@rochester.rr.com;
scirocco-l@scirocco.org
Subject: RE: Exhaust manifold-downpipe studs? Replaceable?
In all my years, I have never, ever successfully used an easy-out UNLESS
liberal applications of heat and penetrating oil preceeded their use. Of
course, if I'd applied the heat/oil BEFORE I tried to remove the bolt/stud,
the need for the easy-out would have been avoided....:)
Try the heat/oil/easy-out first. Then be prepared to drill and tap,
probably going to the next larger size, since you'll inevitably damage the
original threads. Good luck and enjoy the ride.
Larry sandiego16V
-----Original Message-----
From: Bob & Ann [mailto:angus6@socket.net]
Sent: Monday, October 29, 2001 11:36 AM
To: Victor Farren; mpeters6@rochester.rr.com; scirocco-l@scirocco.org
Subject: Re: Exhaust manifold-downpipe studs? Replaceable?
>From my experience with easy-out I would recommend that if you have to go
that way get a set of Hansen easy outs, Their short & hex
headed and I've NEVER seen one break yet,plus they grip better than the long
4 sided ones or the spiral ones
Bob
My experience is that if the easy out breaks while trying to extract frozen
studs, you are screwed. They are made of a substance
that is impervious to drill bits. Here is what I would do:
Victor
>>> "Marc Peterson" <mpeters6@rochester.rr.com> 10/29 10:42 AM >>>
I busted all those studs trying to get the old DP off. Can i just get an
easy-out and screw them out, or will I need to drill them out and retap the
threads? If so, what size tap? Help!
Its an 8 valve.
TIA,
Marc
--
Email LIST problems to: scirocco-l-probs@scirocco.org.
To unsubscibe send "unsubscribe scirocco-l" in the message to
majordomo@scirocco.org
--
Email LIST problems to: scirocco-l-probs@scirocco.org.
To unsubscibe send "unsubscribe scirocco-l" in the message to
majordomo@scirocco.org
--
Email LIST problems to: scirocco-l-probs@scirocco.org.
To unsubscibe send "unsubscribe scirocco-l" in the message to
majordomo@scirocco.org
[Disclaimer]This e-mail is strictly confidential and intended solely for the
addressee. It may contain information which is covered by legal,
professional, or other privilege. If you are not the intended addressee you
must not use, disclose, or copy this transmission. This E-mail is not
intended to impose nor shall it be construed as imposing any legally binding
obligation upon GKN Aerospace Chem-tronics Inc. and/or any of its
subsidiaries or associated companies. Neither GKN Aerospace Chem-tronics
Inc. nor any of its subsidiaries or associated companies gives any
representation or warranty as to the accuracy or completeness of the
contents of this E-mail. GKN Aerospace Chem-tronics Inc. shall not be held
liable to any person resulting from the use of any information contained in
this E-mail and shall not be liable to any person who acts or omits to do
anything in reliance upon it.
--
Email LIST problems to: scirocco-l-probs@scirocco.org.
To unsubscibe send "unsubscribe scirocco-l" in the message to
majordomo@scirocco.org
[Disclaimer]This e-mail is strictly confidential and intended solely for the
addressee. It may contain information which is covered by legal,
professional, or other privilege. If you are not the intended addressee you
must not use, disclose, or copy this transmission. This E-mail is not
intended to impose nor shall it be construed as imposing any legally binding
obligation upon GKN Aerospace Chem-tronics Inc. and/or any of its
subsidiaries or associated companies. Neither GKN Aerospace Chem-tronics
Inc. nor any of its subsidiaries or associated companies gives any
representation or warranty as to the accuracy or completeness of the
contents of this E-mail. GKN Aerospace Chem-tronics Inc. shall not be held
liable to any person resulting from the use of any information contained in
this E-mail and shall not be liable to any person who acts or omits to do
anything in reliance upon it.
--
Email LIST problems to: scirocco-l-probs@scirocco.org.
To unsubscibe send "unsubscribe scirocco-l" in the message to
majordomo@scirocco.org
--
Email LIST problems to: scirocco-l-probs@scirocco.org.
To unsubscibe send "unsubscribe scirocco-l" in the message to majordomo@scirocco.org